Overview

BF5175 sounder beacons is used in Jade Bird Fire JBF-11SF and JBF5000 series fire alarm systems. The sounder beacon gives high decibel alarm sounds and flashes LED light when a fire occurs in public place, and hash Chinese and English voice reporting function. Suitable for indoor (non-residential) public places, such as hotel rooms, office buildings, libraries, theaters, postal buildings, etc.
 

  Product features

• Built-in crested ibis microprocessor that specialized in fire protection.
• Adopt SMT process.
• Two-wire, polarity free loop.
• It is recommended to use twisted cable for the loop. Its cross-sectional area should not be less than 1.5 mm².
• Support three kinds of alarm sounds, can alarm in turns with Chinese and English voice reporting, and can set sound-only alarm and light-only alarm.

 

  Applied scope

• The sounder beacon connect to JBF-11SF and JBF5000 series control panel.
•  Applicable to indoor (non-residential) public places, such as hotel rooms, office buildings, libraries, theaters, post office buildings.
• The application applies to GB 50116-2013 “Code for fire protection design of buildings”

 

  Model name composition

Techinical Data

Environment features

Working temperature	-10～+55℃
Storage temperature	-20～+65℃
Relative humidity	≤95% (no condensation)

Explosion-proof

Explosion-proof mark

NA

Electrical features

Loop voltage	DC18V-28V, modulation type, provided by control panel
Rated voltage	DC 24V
Monitoring current	Loop: ≤ 1.5mA DC 24V: ≤ 40mA
Alarm current	Loop: ≤ 3mA DC 24V: ≤ 125mA
SPL	70.0dB～115.0dB  (DC24V,  A-Weighted)
Frequency cycle	4.0s～5.0s
Flashing rate	1.0Hz～1.5Hz

Communication

Wiring	Four-wire, no polarity
Address range	1～200
Addressing method	Electronic encoder
Max communication distance	1000m

Compatibility

Connect to JBF-11SF and JBF5000 series control panel.

Mechanical features

Appearance	PANTONE T085-2-1
Material	PC (Cover) + ABS (base)
Weight	166g
Dimensions	Φ100mm×H52mm (with base)

Applied standard

1	GB 26851-2011 “Audible and/or visual fire alarm signaling appliances”

 

Installation

 Installation steps

• The sounder beacon adopts unfolded installation.
• After the wiring, fix the base of the sounder beacon to the wall (using M4 bolts), pitch of holes:  45mm~68mm.

 

• Before installation, use an electronic encoder to write the corresponding address to the product. The address should be consistent with the one in the engineering software.
• Connect the two wires of the loop to terminals 1 and 2, polarity-free.
• Connect DC24V to terminals 3 and 4, polarity-free.
• The sounder beacon should be installed after wiring inspection and before debugging to prevent losses caused by improper installation

The sounder beacon wiring diagram (see figure 2)

Commissioning

• First use electronic encoder to write address to the sounder beacon. The address range is 1 ~ 200.
• After successfully writing the address, connect the sounder beacon to the control panel to register it.
• In case of fire, the control panel sends out fire command, and the sounder beacon gives out sound alarm, voice reporting and LED flashing light alarms.
• Set working mode of the sounder beacon through special address:

Working mode	Special address	Notes
Alarming type	201
Sound only	202
Light only	203

 

• Set alarm sound of the sounder beacon through special address:

Sound alarm	Special address	Notes
Alarm sound and Chinese/English voice reporting	204
beep and Chinese/English voice reporting	205
honk and Chinese/English voice reporting	209

 

• Set status of the sounder beacon through special address:

Status	Special address	Notes
Addressable	206
Reset to factory status	208	Sound alarm, alarming type, addressable

 

Troubleshooting

Trouble	Causes	Solutions	Notes
The control panel reports fault	Loop not connected.	Rewire the loop.
	The actual address of the sounder beacon is not the same as the one in engineering software.	Write address to the product following the project engineering software.
Unable to register the device	The device is not addressed.	Address the device using encoder.
	Loop is not correctly connected	Check the wiring.
	Address number is out of range	Address range: 1-200

 

Maintenance

• Daily maintenance, maintenance, and calibration
• Conduct alarm test regularly, every six months recommended.

 

Out-of-box check

Open the package and check the follow parts are included:

sounder beacon	125/package, base not included
Manual	10/package

After opening the package, please check the appearance and functions of the product. Should there be any loss or damage to the sounder beacon, please contact us soon. Once determined that the damage is not caused by human factors, we will replace it for the customer immediately.
 

Disclaimer

• The Company reserves the right to finally interpret this manual.
• The steps in this manual must be strictly followed for installation and commissioning.